Specification
| Power Range | 350 to 650 Watts |
| Version/span> | Single Phase 230V, 50Hz, A.C Supply |
| Degree of protection | IP68 |
| Class of insulation | E |
| Delivery size | Drainage : 1¼”, Sewage : 1½” |
| Max. ambient temp. | 40°C |
| Max. liquid temp. | 40°C |
| pH value | 6 – 8.5 |
Tiny Sewage & Drainage Pumps (TPS & TSS – SERIES)
Quick description:
Tormac tiny sewage pumps, used in domestic and light commercial applications, Tormac tiny Sewage pumps are come with two variant TPS & TSS come with plastic and stainless stell body with thermoplastic impeler and the carbon ceramic mechanical seal, with special design considerations enabling solids to pass without clogging the pump.
Availability:
In Stock
Materials of Construction
| Part Name | TPS Series | TSS Series |
| Pump body | Plastic | Stainless Steel |
| Impeller | Thermoplastic | Thermoplastic |
| Shaft | S.S 304 | S.S 304 |
| Pump casing | Plastic | Stainless Steel |
| Mechanical seal | Carbon Ceramic | Carbon Ceramic |
Applications
- Residential drainage and sewage
- Gardening
- Dewatering
You May Also like
Stainless Steel Submersible Pumps 10″ (TS/250 – Series-60Hz)
STAINLESS STEEL SUBMERSIBLE PUMPS 10”, TS / TN – SERIES Tormac stainless steel submersible pumps are ingeniously designed and developed employing latest engineering software’s, high-tech machinery, tools and cutting edge of pumping technology to deliver the best possible hydraulic efficiency. The complete stainless steel construction not only prevents the pumps from corrosion but also exceptionally increases the lifespan. The integrated and most modern quality assurance systems used at every stage of the production and flawless workmanship ensure sustained and consistent operation.
All these submersible pumps are the multistage single suction centrifugal type, provided with integral check-valve and NEMA standard coupling. These pumps are available with fabricated impellers and diffusers made of AISI 304/316 and the shaft is made of AISI 304/431. The integral check valve prevents backflow and reduces the risk of water hammer which paves the way for trouble-free performance. The suction screen is designed with utmost care so as not to reduce the inflow of water and at the same time to prevent damage to the pump and clogging due to the entry of sand and other foreign particles.
Water Circulatory Pumps (TWC – SERIES)
“Tormac Water Circulatory pumps are used to circulate hot / cold water with adequate pressure in HVAC systems. All parts & components have been uncompromisingly tested to ensure trouble free performance and safety operation. The motor is of 2 pole asynchronous and squirrel cage type and consists of canned rotor portion. All the rotating parts are in touch with pumped liquid and thus it acts as lubricant to rotor, shaft & thrust bearings. An air vent plug is provided in the rear-end. The centrifugal impeller is of radial & closed type with corrosion resistant curved blades. Impeller, shaft with rotor, thrust bearing pad and the intermediate rings are assembled as a single unit to avoid the misalignment of the bearings. The thrust bearing is designed to withstand high axial thrust load. The particular model of pumps are equipped with a rotary switch in the terminal box that can be used to control the speed in 3 different levels based on the requirement. For trouble free operation the temperature of the pumped liquid should not exceed the specified level, the minimum inlet pressure should be maintained (to avoid cavitations) and dry run must totally be avoided. As the motor is impedance protected and consequently short-circuit proof, no additional motor protection is required. The pump is provided with standard length of cable lead out with plug. These circulatory pumps are generally used in tandem with heating systems. “
CENTRIFUGAL MONOBLOCK PUMPS (TM – Series – Higher Range)
Tormac Centrifugal pump’s volute chamber and impellers are carefully designed to give the best possible hydraulic and suction lift characteristics. All dimensions and performances are according to EN733- DIN 24255 standards. Most modern and highly sophisticated machinery and technology are employed in the manufacture of these pumps using quality raw material,dynamically balanced impellers, seals and ball bearings to ensure long life. Dynamically balanced rotor ensures vibration and noise free operation. Shaft is made of quality steel, precision ground of ample size for transmitting the rated Horse Power.
HORIZONTAL MULTISTAGE PUMPS (TH Series)
Tormac TH Horizontal Multistage Centrifugal pumps are specially designed to facilitate pressure boosting and are best suited for a wide range of applications. The vital components viz. impellers, diffusers, and shaft used in these pumps are made of corrosion resistance high quality Stainless Steel which ensure a smooth and trouble free performance helps to pump safe and hygienic drinking water system. The prime mover of this product is robust in construction and built with thermal overload protection (only in single phase motors). High quality mechanical seals are used to ensure less friction / power loss.