Tormac End suction pumps with volute casing DIN 16 DIN 2532/2533 single stage end suction with bearing housing, Dimension in accordance with DIN 24255. End suction pumps are single stage centrifugal, non-self-priming, volute pumps. These pumps feature horizontal shaft components with axial suction and impellers and radial discharge ports. Pumps volute chamber and impellers are carefully designed to give the best possible and suction lift characteristics. Most modern and highly sophisticated machinery and technology are employed in the manufacture of these pumps using quality raw material, dynamically balanced impellers, seal and bearings to ensure long life.
In Stock
| Outlet size range | DN32 to DN150mm |
| Flow range | Upto 550 m3/h |
| Total Head range | Upto 100m |
| Operating temperature with soft packed stuffing box | 90˚C |
| Operating temperature with mechanical seal | 90˚C |
| Maximum working pressure | 16bar |
| RPM | 1450 / 2900 |
| Pump Parts | Type – C | Type – B | Type – S |
| Pump casing | Cast Iron | Cast Iron | AISI 304 |
| Impeller | Cast Iron | Zinc free Bronze | AISI 304 |
| Shaft | EN – 8 | EN – 8 | AISI 304 / AISI 316 |
| Sleeve | AISI 410 | AISI 410 | AISI 410 |
Tormac centrifugal openwell pump’s volute chamber and impellers are carefully designed to give the best possible hydraulic efficiency and suction lift characteristic. State of the art machinery, technology and expertise gained over the years are employed in the manufacture of these pumps using quality raw material, journal bushes and dynamically balanced rotating components to ensure long life. Tormac openwell submersible prime movers are squirrel cage water filled and water-cooled rewindable type made of a special waterproof pure electrolytic copper insulated with synthetic film material. A uniquely designed thrust bearings with high thrust capacity and good quality shaft seals are used to enhance the strength and durability. All single-phase motors are incorporated with thermal overload protector. All Tormac openwell submersible pumps are produced in accordance with ISO 9001 standards.
Tormac offers a comprehensive range of A.C. Induction motors in standard and premium efficiency designs for wide range of applications. These motors are synchronous type with constant speed suitable for continuous duty operations. Stator is made of low watt loss steel laminations to deliver high efficiency. Dynamically balanced rotor and high quality bearings ensure vibration and noise free operations. The varnish impregnated windings are made of high-grade enameled copper wire. Shaft is made of high quality steel, precision ground of ample size for transmitting the rated horsepower. Construction of motor frames and usage of quality materials result in high performance and low temperature rise, thereby increasing the life cycle of the motor. High-grade cast iron / Die-cast Aluminum components machined with close tolerance and high quality, heavy duty bearings are used to ensure better efficiency and longer life. All three phase motors require adequate control systems with necessary protections. Motors are available with IE1(EFF-2), IE2(EFF-1), IE-3(Premium Efficiency) versions with B3, B5 & B14 mounting dimensions to cater various applications.
“Tormac Water Circulatory pumps are used to circulate hot / cold water with adequate pressure in HVAC systems. All parts & components have been uncompromisingly tested to ensure trouble free performance and safety operation. The motor is of 2 pole asynchronous and squirrel cage type and consists of canned rotor portion. All the rotating parts are in touch with pumped liquid and thus it acts as lubricant to rotor, shaft & thrust bearings. An air vent plug is provided in the rear-end. The centrifugal impeller is of radial & closed type with corrosion resistant curved blades. Impeller, shaft with rotor, thrust bearing pad and the intermediate rings are assembled as a single unit to avoid the misalignment of the bearings. The thrust bearing is designed to withstand high axial thrust load. The particular model of pumps are equipped with a rotary switch in the terminal box that can be used to control the speed in 3 different levels based on the requirement. For trouble free operation the temperature of the pumped liquid should not exceed the specified level, the minimum inlet pressure should be maintained (to avoid cavitations) and dry run must totally be avoided. As the motor is impedance protected and consequently short-circuit proof, no additional motor protection is required. The pump is provided with standard length of cable lead out with plug. These circulatory pumps are generally used in tandem with heating systems. “
Tormac ECO series submersible motors are ingeniously designed and developed employing latest engineering software’s, high-tech machinery & tools with the complement of cutting edge technology for hardwearing and maintenance free operations and to ensure relentless performance.
The electrical conditions such as voltage, frequency and the operating conditions are taken into account in designing the winding and cooling system. Tried and trusted indigenously improved design, combined with the most optimized efficiency in electromagnetic design exceptionally ensures trouble free performance. The integrated and most modern quality assurance systems used at every stage of production and flawless workmanship lead to sustained and consistent operation.
Tormac ECO series motors are squirrel cage, water filled and water cooled rewindable type. The winding of these two pole motors are made of a special water proof wire of pure electrolytic copper insulated with synthetic film or thermoplastic material. The stator shell, housings shell & motor base are made of fabricated S.S 304/316 which prevents the motor from corrosion.
These motors are pre-filled with environmentally safe deionized water which acts as a lubricant & coolant. The prefilled water level to be ensured at the time of installation. A uniquely designed thrust bearing with high thrust capacity and good quality shaft seals are used to enhance the strength & durability. All single phase motors are supplied with suitable control boxes. The main advantage of rewindable motor construction is making the repair and rewinding easier and hassle free at field levels. All Tormac motors are produced in accordance with ISO 9001 standards and mounting dimensions with NEMA standard.
