Tormac centrifugal openwell pump’s volute chamber and impellers are carefully designed to give the best possible hydraulic efficiency and suction lift characteristic. State of the art machinery, technology and expertise gained over the years are employed in the manufacture of these pumps using quality raw material, journal bushes and dynamically balanced rotating components to ensure long life. Tormac openwell submersible prime movers are squirrel cage water filled and water-cooled rewindable type made of a special waterproof pure electrolytic copper insulated with synthetic film material. A uniquely designed thrust bearings with high thrust capacity and good quality shaft seals are used to enhance the strength and durability. All single-phase motors are incorporated with thermal overload protector. All Tormac openwell submersible pumps are produced in accordance with ISO 9001 standards.
In Stock
| Series | TOH |
| Power Range | 0.37 – 1.5 kW (1Ph) 0.75 – 18.5 kW (3Ph) |
| Speed | 2900 |
| Frequency | 50Hz |
| Power Version | Single Phase 200 – 220V Three Phase 380 – 415V |
| Degree of Protection | IP – 58 |
| Duty type | S1 Continuous |
| Max. Start per hour | 6 times |
| Head Range | 76 m / 250 ft |
| Outlet Size | 1”, 1½”, 2”, 2½”, 3”, 4” & 6” |
| Liquid Temperature | 33°C |
| Class of Insulation | “Y” |
| Flow Range | 160 m3/h |
Tormac tiny sewage pumps, used in domestic and light commercial applications, Tormac tiny Sewage pumps are come with two variant TPS & TSS come with plastic and stainless stell body with thermoplastic impeler and the carbon ceramic mechanical seal, with special design considerations enabling solids to pass without clogging the pump.
Tormac End suction pumps with volute casing DIN 16 DIN 2532/2533 single stage end suction with bearing housing, Dimension in accordance with DIN 24255. End suction pumps are single stage centrifugal, non-self-priming, volute pumps. These pumps feature horizontal shaft components with axial suction and impellers and radial discharge ports. Pumps volute chamber and impellers are carefully designed to give the best possible and suction lift characteristics. Most modern and highly sophisticated machinery and technology are employed in the manufacture of these pumps using quality raw material, dynamically balanced impellers, seal and bearings to ensure long life.
“Tormac Water Circulatory pumps are used to circulate hot / cold water with adequate pressure in HVAC systems. All parts & components have been uncompromisingly tested to ensure trouble free performance and safety operation. The motor is of 2 pole asynchronous and squirrel cage type and consists of canned rotor portion. All the rotating parts are in touch with pumped liquid and thus it acts as lubricant to rotor, shaft & thrust bearings. An air vent plug is provided in the rear-end. The centrifugal impeller is of radial & closed type with corrosion resistant curved blades. Impeller, shaft with rotor, thrust bearing pad and the intermediate rings are assembled as a single unit to avoid the misalignment of the bearings. The thrust bearing is designed to withstand high axial thrust load. The particular model of pumps are equipped with a rotary switch in the terminal box that can be used to control the speed in 3 different levels based on the requirement. For trouble free operation the temperature of the pumped liquid should not exceed the specified level, the minimum inlet pressure should be maintained (to avoid cavitations) and dry run must totally be avoided. As the motor is impedance protected and consequently short-circuit proof, no additional motor protection is required. The pump is provided with standard length of cable lead out with plug. These circulatory pumps are generally used in tandem with heating systems. “
Tormac TH Horizontal Multistage Centrifugal pumps are specially designed to facilitate pressure boosting and are best suited for a wide range of applications. The vital components viz. impellers, diffusers, and shaft used in these pumps are made of corrosion resistance high quality Stainless Steel which ensure a smooth and trouble free performance helps to pump safe and hygienic drinking water system. The prime mover of this product is robust in construction and built with thermal overload protection (only in single phase motors). High quality mechanical seals are used to ensure less friction / power loss.
Select at least 2 products
to compare
