Specification
| Power Range | 350 to 650 Watts |
| Version/span> | Single Phase 230V, 50Hz, A.C Supply |
| Degree of protection | IP68 |
| Class of insulation | E |
| Delivery size | Drainage : 1¼”, Sewage : 1½” |
| Max. ambient temp. | 40°C |
| Max. liquid temp. | 40°C |
| pH value | 6 – 8.5 |
Tiny Sewage & Drainage Pumps (TPS & TSS – SERIES)
Quick description:
Tormac tiny sewage pumps, used in domestic and light commercial applications, Tormac tiny Sewage pumps are come with two variant TPS & TSS come with plastic and stainless stell body with thermoplastic impeler and the carbon ceramic mechanical seal, with special design considerations enabling solids to pass without clogging the pump.
Availability:
In Stock
Materials of Construction
| Part Name | TPS Series | TSS Series |
| Pump body | Plastic | Stainless Steel |
| Impeller | Thermoplastic | Thermoplastic |
| Shaft | S.S 304 | S.S 304 |
| Pump casing | Plastic | Stainless Steel |
| Mechanical seal | Carbon Ceramic | Carbon Ceramic |
Applications
- Residential drainage and sewage
- Gardening
- Dewatering
You May Also like
Vertical Open Well Submersible Pumps (TOV Series)
Tormac centrifugal openwell pump’s volute chamber and impellers are carefully designed to give the best possible hydraulic efficiency and suction lift characteristic. State of the art machinery, technology and expertise gained over the years are employed in the manufacture of these pumps using quality raw material, journal bushes and dynamically balanced rotating components to ensure long life. Tormac openwell submersible prime movers are squirrel cage water filled and water-cooled rewindable type made of a special waterproof pure electrolytic copper insulated with synthetic film material. A uniquely designed thrust bearings with high thrust capacity and good quality shaft seals are used to enhance the strength and durability. All single-phase motors are incorporated with thermal overload protector. All Tormac openwell submersible pumps are produced in accordance with ISO 9001 standards.
CENTRIFUGAL MONOBLOCK PUMPS (TM – Series – Higher Range)
Tormac Centrifugal pump’s volute chamber and impellers are carefully designed to give the best possible hydraulic and suction lift characteristics. All dimensions and performances are according to EN733- DIN 24255 standards. Most modern and highly sophisticated machinery and technology are employed in the manufacture of these pumps using quality raw material,dynamically balanced impellers, seals and ball bearings to ensure long life. Dynamically balanced rotor ensures vibration and noise free operation. Shaft is made of quality steel, precision ground of ample size for transmitting the rated Horse Power.
Water Circulatory Pumps (TWC – SERIES)
“Tormac Water Circulatory pumps are used to circulate hot / cold water with adequate pressure in HVAC systems. All parts & components have been uncompromisingly tested to ensure trouble free performance and safety operation. The motor is of 2 pole asynchronous and squirrel cage type and consists of canned rotor portion. All the rotating parts are in touch with pumped liquid and thus it acts as lubricant to rotor, shaft & thrust bearings. An air vent plug is provided in the rear-end. The centrifugal impeller is of radial & closed type with corrosion resistant curved blades. Impeller, shaft with rotor, thrust bearing pad and the intermediate rings are assembled as a single unit to avoid the misalignment of the bearings. The thrust bearing is designed to withstand high axial thrust load. The particular model of pumps are equipped with a rotary switch in the terminal box that can be used to control the speed in 3 different levels based on the requirement. For trouble free operation the temperature of the pumped liquid should not exceed the specified level, the minimum inlet pressure should be maintained (to avoid cavitations) and dry run must totally be avoided. As the motor is impedance protected and consequently short-circuit proof, no additional motor protection is required. The pump is provided with standard length of cable lead out with plug. These circulatory pumps are generally used in tandem with heating systems. “
A.C. Induction Motor
Tormac offers a comprehensive range of A.C. Induction motors in standard and premium efficiency designs for wide range of applications. These motors are synchronous type with constant speed suitable for continuous duty operations. Stator is made of low watt loss steel laminations to deliver high efficiency. Dynamically balanced rotor and high quality bearings ensure vibration and noise free operations. The varnish impregnated windings are made of high-grade enameled copper wire. Shaft is made of high quality steel, precision ground of ample size for transmitting the rated horsepower. Construction of motor frames and usage of quality materials result in high performance and low temperature rise, thereby increasing the life cycle of the motor. High-grade cast iron / Die-cast Aluminum components machined with close tolerance and high quality, heavy duty bearings are used to ensure better efficiency and longer life. All three phase motors require adequate control systems with necessary protections. Motors are available with IE1(EFF-2), IE2(EFF-1), IE-3(Premium Efficiency) versions with B3, B5 & B14 mounting dimensions to cater various applications.